Experiencing a black display on your GoPro Black 6 can be frustrating, but don’t despair! Resetting the display is a relatively straightforward procedure that can often resolve this issue. In this comprehensive guide, we will provide a step-by-step approach to successfully resetting the display of your GoPro Black 6, ensuring that you can capture stunning footage once again.
To begin, ensure that your GoPro Black 6 is powered off. Locate the two buttons on the side of the camera: the Mode button and the Shutter/Power button. Press and hold both buttons simultaneously for about 10 seconds. You will notice a red LED light begin to blink, indicating that the camera is entering reset mode. Continue holding the buttons until the LED light turns off, which signifies that the reset process is complete.
After resetting the display, turn on your GoPro Black 6 and check if the issue persists. In most cases, this procedure should resolve the black display problem. However, if the issue remains, it is advisable to consult the official GoPro support website or contact their customer service team. They can provide additional troubleshooting steps or assist you in determining if a more comprehensive repair is necessary.
Troubleshooting a Black GoPro Display
If your GoPro Black 6’s display has gone black, there are a few things you can try to troubleshoot and resolve the issue:
1. Restart Your GoPro
A simple restart can often resolve display issues. To restart your GoPro:
- Power off the GoPro by pressing and holding the power button until the device turns off.
- Remove the battery and memory card.
- Reinsert the battery and memory card.
- Power on the GoPro by pressing and releasing the power button.
If the display remains black, try the following steps:
- Connect the GoPro to a computer using a USB cable.
- Open the GoPro desktop application or use the camera’s built-in controls to perform a factory reset.
- If the display still remains black, contact GoPro support for further assistance.
2. Check the Battery
Ensure that the battery is fully charged and properly inserted into the camera. A weak or depleted battery can cause display issues.
3. Clean the Display
Wipe the display with a soft, dry cloth to remove any dirt or debris that may be interfering with the display’s functionality.
4. Check the LCD Ribbon Cable
The LCD ribbon cable connects the display to the motherboard. If the cable is loose or damaged, it can cause display issues. To check the cable, follow these steps:
| Steps | Instructions |
|---|---|
| Remove the battery and memory card. | Open the camera’s back cover. |
| Locate the LCD ribbon cable. | Disconnect and reconnect the cable. |
| Reassemble the camera. | Check if the display is functioning properly. |
Resetting the GoPro Hero6 Black
Factory Reset
If your GoPro Hero6 Black is experiencing issues such as a black display, a factory reset may resolve the problem. To perform a factory reset, follow these steps:
- Turn on your GoPro Hero6 Black.
- Swipe down from the top of the screen to access the Quick Settings menu.
- Scroll down and tap on “Preferences.”
- Scroll down and tap on “Reset Camera.”
- Confirm that you want to reset the camera by tapping on “Yes.”
Your GoPro Hero6 Black will now restart and all of your settings will be restored to their default values.
Hard Reset
If a factory reset does not resolve the issue, you may need to perform a hard reset. This will erase all of your data from the camera, so be sure to back up any important files before proceeding. To perform a hard reset, follow these steps:
- Turn off your GoPro Hero6 Black.
- Press and hold the Power button and the Mode button simultaneously for 10 seconds.
- Release the buttons when the camera powers on and the GoPro logo appears on the screen.
Your GoPro Hero6 Black will now restart and all of your data will be erased.
| Factory Reset | Hard Reset |
|---|---|
| Restores camera settings to default values | Erases all camera data |
| Does not erase data | Erases all data |
| Can be performed multiple times | Should only be performed as a last resort |
Performing a Hard Reset
A hard reset is a more drastic measure that will erase all settings and data from your GoPro. It is recommended as a last resort if other troubleshooting methods have not been successful.
To perform a hard reset:
- Power off the GoPro.
- Hold down the Mode and Shutter buttons simultaneously.
- Press the Power button and continue holding all three buttons for 10 seconds.
- Release the buttons.
The GoPro will now restart and the factory default settings will be restored.
Additional Information
Here are some additional details about performing a hard reset on a GoPro Black 6:
- The hard reset process will erase all settings, preferences, and data from the GoPro, including Wi-Fi passwords, custom modes, and recorded footage.
- It is important to back up any important data before performing a hard reset.
- A hard reset can be performed even if the GoPro is not responding or the display is black.
Troubleshooting Table
| Symptom | Solution |
|---|---|
| The GoPro will not turn on after performing a hard reset. | Try connecting the GoPro to a charger and allowing it to charge for a few minutes. |
| The GoPro turns on but the display is still black. | The display may be damaged. Contact GoPro support for assistance. |
Factory Resetting the Device
If you are unable to resolve the issue using the previous methods, you may need to factory reset your GoPro Black 6. This will erase all data and settings from the device, so be sure to back up any important files before proceeding.
To factory reset your GoPro Black 6, follow these steps:
1. Power Off the Device
Press and hold the Power button until the device turns off.
2. Remove the Battery
Open the battery door and remove the battery.
3. Reinsert the Battery
Insert the battery back into the device.
4. Press and Hold the Power and Shutter Buttons Simultaneously
While holding down the Power button, press and hold the Shutter button. Continue holding both buttons until the device turns on and the GoPro logo appears. Once the logo appears, release both buttons.
The device will now enter the factory reset mode. Use the Shutter button to navigate through the menu and select the “Reset” option. Press the Power button to confirm your selection.
The device will now reset to its factory settings. Once the reset is complete, the device will automatically restart.
Manual Reset Procedure
To manually reset your GoPro Black 6:
1. Power off the camera by holding down the Power/Mode button for a few seconds.
2. Remove the battery from the camera.
3. Wait for a minute or two.
4. Reinsert the battery into the camera.
5. Hold down the Power/Mode button and the Shutter button simultaneously for 10 seconds.
The camera will reset to its factory default settings.
Here is a table summarizing the steps for manually resetting your GoPro Black 6:
| Step | Action |
|---|---|
| 1 | Power off the camera. |
| 2 | Remove the battery. |
| 3 | Wait for a minute or two. |
| 4 | Insert the battery. |
| 5 | Press the Power/Mode button and the Shutter button simultaneously for 10 seconds. |
Identifying the Reset Button
The reset button on the GoPro Hero6 Black is a small, elongated button located on the bottom of the camera, next to the USB-C port. It is recessed within a small hole, making it difficult to press accidentally.
To access the reset button, you will need to use a small, pointed object, such as a paperclip or a toothpick. Insert the object into the hole and press the reset button firmly for about 10 seconds, or until the camera beeps and the display turns on.
If you are unable to access the reset button with a pointed object, you can also try using a magnet. Place the magnet over the hole where the reset button is located and hold it there for about 10 seconds. This should also trigger a reset.
| Method | Steps |
|---|---|
| Using a pointed object | Insert the object into the hole and press the reset button for about 10 seconds, or until the camera beeps and the display turns on. |
| Using a magnet | Place the magnet over the hole where the reset button is located and hold it there for about 10 seconds. |
Initiating the Factory Reset
Factory resetting your GoPro Black 6 can resolve various issues, including a black display. It erases all user settings, preferences, and data from the device, restoring it to its default state.
7. Confirm the Reset
After entering the confirmation code, you’ll be prompted to confirm the reset. To proceed, select ‘Reset’ or ‘Yes’. Your GoPro will now begin the reset process, which may take a few minutes to complete.
Note: Once the reset is complete, your GoPro will automatically restart. You’ll need to re-configure the device’s settings and preferences as desired.
| Action | Result |
|---|---|
| Select ‘Reset’ or ‘Yes’ | Confirms the factory reset and initiates the process |
| GoPro restarts automatically | Indicates completion of the reset |
Resetting Without Buttons
If your GoPro Black 6 display is black and you cannot access the buttons, you can still reset the device using the following steps:
1. Power Off the GoPro
Hold down the power button for 10 seconds to turn off the GoPro.
2. Remove the Battery
Open the battery door and remove the battery.
3. Insert a Paperclip
Locate the small reset hole on the bottom of the GoPro. Insert a paperclip or similar object into the hole and press down for 5 seconds.
4. Reinstall the Battery
Insert the battery back into the GoPro and close the door.
5. Power On the GoPro
Hold down the power button until the GoPro turns on.
6. Restore Default Settings
Navigate to the Settings menu and select “Reset Camera”.
7. Confirm Reset
Select “Yes” to confirm the reset.
8. Reformat the Memory Card
Go to the Settings menu and select “Format Card”. Select “Yes” to reformat the memory card. This will erase all data on the card, so make sure to back up any important files first.
| Step | Description |
|---|---|
| 1 | Power off the GoPro and remove the battery |
| 2 | Insert a paperclip into the reset hole |
| 3 | Reinstall the battery and turn on the GoPro |
| 4 | Restore default settings and reformat the memory card |
Restarting the GoPro
If your GoPro Black 6 display is black, restarting the device may help resolve the issue. Here are the detailed steps on how to restart the GoPro:
1. Remove the Battery
Start by removing the battery from the GoPro. To do this, slide the battery latch and pull the battery out.
2. Insert the Battery
Once the battery is removed, insert it back into the GoPro. Make sure it’s correctly aligned and securely in place.
3. Press the Power Button
Press and hold the power button for about 5 seconds. The GoPro will turn on.
4. Factory Reset Option
If the display remains black after restarting, you may consider performing a factory reset. To do this, follow these steps:
5. Enter Settings Menu
Press the mode button to enter the settings menu.
6. Navigate to Preferences
Scroll down and select the “Preferences” option.
7. Select Reset Camera
Under the “Preferences” menu, find the “Reset Camera” option and select it.
8. Confirm Reset
A confirmation message will appear. Select “Yes” to confirm the factory reset.
9. Resetting Display Settings
Once the factory reset is complete, you can adjust the display settings to ensure it’s working correctly. Follow these steps:
| Setting | Description |
|---|---|
| Display Modes | Select “Always On” or “Auto” to keep the screen active while shooting. |
| Brightness | Adjust the brightness level to improve visibility in different lighting conditions. |
| Orientation | Choose the screen orientation (Front or Rear) based on your shooting preferences. |
Troubleshooting Reset Failures
If the reset process fails, try the following troubleshooting steps:
1. Ensure the Battery is Sufficiently Charged
Make sure your GoPro has at least 10% battery life before attempting a reset. A low battery can interfere with the reset process.
2. Use a Different USB Cable or Port
Try connecting your GoPro to a different USB cable or port on your computer. Some cables or ports may not provide enough power for the reset to complete successfully.
3. Contact GoPro Support
If you have tried the above steps and the reset still fails, contact GoPro Support for further assistance.
4. Check for Firmware Updates
A firmware update may address reset-related issues. Check for and install any available firmware updates for your GoPro.
5. Remove the Battery and Memory Card
Turn off your GoPro, remove the battery, and remove the memory card. Wait for a few minutes and then reinsert the battery and memory card. This may reset the GoPro’s settings and resolve the display issue.
6. Perform a Hard Reset
Press and hold the Mode, Shutter, and Power buttons simultaneously for 10 seconds. This will perform a hard reset of your GoPro, which may resolve the display problem.
7. Check the Display Cable
Open the back of the GoPro and inspect the display cable for loose connections or damage. If the cable is loose, reconnect it securely. If it is damaged, you may need to replace the display.
8. Inspect the Display for Damage
Look for any signs of physical damage on the display, such as cracks or scratches. Damage to the display may prevent it from functioning properly.
9. Try a Different Display
If possible, connect your GoPro to a different display, such as an external monitor or TV. If the display issue persists on the external display, it may indicate a problem with the GoPro itself.
10. Consider Battery Replacement
A worn-out battery can sometimes cause power issues that manifest as a black display. If you have been using the same battery for an extended period, consider replacing it with a new one.
| Troubleshooting Step | Description |
|—|—|
| Check Battery Charge | Ensure sufficient battery life for reset. |
| Use Different USB | Try an alternative USB cable or port. |
| Contact GoPro Support | Seek assistance for unresolved reset failures. |
| Check Firmware Updates | Install any available firmware updates. |
| Remove Battery and SD Card | Reset settings by removing and reinserting these components. |
| Hard Reset | Press Mode, Shutter, and Power together for 10 seconds. |
| Check Display Cable | Inspect cable for loose connections or damage. |
| Inspect Display | Look for physical damage on the display. |
| Try Different Display | Connect to an external monitor to troubleshoot display issue. |
| Consider Battery Replacement | Replace worn-out battery if necessary. |
How to Reset GoPro Black 6 Display If It’s Black
If the display on your GoPro Black 6 camera is black and unresponsive, it may require a reset. Here are the steps to reset the GoPro Black 6 display:
- Remove the battery from the camera.
- Insert a paperclip or similar object into the small hole labeled “Reset” on the side of the camera.
- Hold the “Reset” button for at least 5 seconds.
- Reinsert the battery and power on the camera.
Once the camera has been reset, the display should be restored to normal functionality.
People Also Ask
Why is my GoPro Black 6 display black?
There are several reasons why the GoPro Black 6 display may be black, including a software glitch, a loose or damaged cable, or a faulty display.
How do I fix a black screen on my GoPro Black 6?
To fix a black screen on your GoPro Black 6, try the following steps:
- Reset the camera.
- Inspect the cable connecting the display to the camera for any damage or loose connections.
- Contact GoPro support for further assistance.
Can I replace the display on my GoPro Black 6 myself?
Yes, it is possible to replace the display on your GoPro Black 6 yourself.
However, it requires some technical knowledge and careful handling. You can find replacement displays online and follow detailed guides to complete the repair.
